Why Does My Vehicle’s Engine Burn Oil?

The simple answer: It’s probably wearing out. Over time, the piston rings have likely become worn or stuck in their grooves, preventing them from sealing tightly against the cylinder wall. The tiny gap that has formed between the ring and cylinder wall allows oil to enter the combustion chamber and burn. Worn valve seals produce the same effect. You may also be using an oil with poor resistance to heat, causing the oil to evaporate.

The detailed answer: Engines can burn oil due to a few reasons.

• Worn or stuck piston rings
• Worn valve seals
• Unstable motor oil
• Excessively low oil viscosity

Most stock automotive pistons contain three rings. The top and second rings are responsible for pressing tightly against the cylinder wall andnew-rings-image sealing the combustion chamber, keeping combustion gases in and oil out. The oil ring scrapes oil off the cylinder wall on the way down the cylinder, depositing it back into the oil sump. Because an extremely thin film of oil lubricates the ring/cylinder wall interface, it is normal for some oil to burn during combustion. What constitutes “normal” oil consumption, however, depends on the engine.

Valve seals also help prevent oil from entering the combustion chamber. Because oil is present to lubricate the seals and keep them pliable, some oil will burn during combustion. Even so, newer engines shouldn’t burn much oil. In fact, you shouldn’t need to add much – if any – top-off oil between oil changes, particularly if you’re using a high-quality synthetic oil. But be sure to check your oil regularly just in case.

Blame it on friction

Despite our best efforts, things eventually wear out, including engines. Worn rings can allow a gap to form between the ring face and cylinder wall. During operation, oil can slip past the rings into the combustion chamber, where it burns. Worn valve seals also contribute to oil consumption.

Stuck rings as a result of heavy deposits can result in the same scenario. Using a conventional oil that fails to resist chemical breakdown can lead to ring-land deposits, which cause the rings to stick. When this happens, the piston rings no longer float in the cylinder liner and can lead to increased oil consumption (in addition to wear).

Where did the oil go?

porta-engine-imageYou may also be using a motor oil with poor heat resistance. Conventional motor oils contain light, unstable molecules that more easily lift out of the solution in the presence of high heat, much like the heat of the sun lifts water molecules out of a puddle. As a result, the oil level drops as the oil is converted to carbon deposits throughout your engine.

This is likely what happened with my Oldsmobile Intrigue back in the dark ages before I started working at AMSOIL. I used a cheap oil from a big-box retailer, and scratched my head in befuddlement each time the oil on the dipstick registered low. I even had a mechanic check for oil leaks (he found none).

 

Use the correct viscosity of oil

Another possibility, albeit less likely, is you’re not using the correct viscosity of motor oil for your engine. Viscosity is defined as resistance to flow, but it’s easier to think of it as thickness. The lower the viscosity, the thinner the oil. As you can imagine, thinner oil will slip past worn rings or valve seals easier than thicker oil.

The correct oil viscosity for your engine is probably printed on the oil filler cap. If not, you can find it in the owner’s manual or the AMSOIL Product Guide.

Some manufacturers recommend a range of viscosities depending on your climate (e.g. 5W-20 when it’s cold, 10W-30 when it’s above 0ºF). Using the highest recommended viscosity can help close the gap between the rings and cylinder wall, reducing oil consumption.

Use an oil that fights wear and deposits

You can fight wear and deposits that lead to oil consumption by using a high-quality synthetic motor oil. AMSOIL Signature Series Synthetic Motor Oil delivers:

75% more engine protection against horsepower loss and wear than required by a leading industry standard*, extending the life of vital components like pistons and cams
93% cleaner pistons than required by a leading industry standard*

*Based on independent testing of AMSOIL Signature Series 5W-30, in ASTM D7320 as required by API SN specification.

Personal experience

My own VW Jetta 2.0 known to use oil – we solved that with the engine flush and “classic” 5W-40 European oil.  The flush seemed to cause something to do with the rings to re-seal.. Can’t say more than that but it certainly eliminated a quart usage/burning over 3000 miles.
I did this after dozens of my own customers found the same results so my own customers sold me on this AMSOIL product!!

 

top dead center valve timing

Why Does My Engine Knock? 3 Possible Explanations. John Baker|Aug 06, 2019 10:56 AM There are a few different reasons your engine might make a knocking, ticking or pinging sound. Let’s break each down and talk about what might be happening. Is it an engine knocking sound, tick or ping? One driver’s knock is another driver’s tick. Or ping. […]

cleaning filter surface

Changing the Oil in your Motorcycle John Baker|Mar 09, 2020 9:20 AM Guest Blog Post by Monica Pretzl Changing oil in your motorcycle is relatively quick and easy. It’s also important; regular oil changes prolong engine life and keep your bike running smoothly all season. We broke down the process into step-by-step directions for both […]

Synthetic Air Tool Oil

Premium Air Tool Protection New Synthetic Air Tool Oil provides smooth operation, reduces wear and extends tool life. Air (pneumatic) tools are commonly used amongst automotive enthusiasts, mechanics and craftsmen. Powered by compressed air, they provide exceptional precision and higher power-to-weight ratios than their conventional power-tool counterparts, making them popular choices for those working with […]

Reposting – Top 3 Single-Track Dirt Bike Trails in the Upper Midwest Kerry Johnson|Aug 24, 2016 2:53 PM   We sat down with dirt bike enthusiast and AMSOIL Mechanical Lab Technician, Ben Grembowski, to learn about his favorite places in Minnesota to ride the trails. With 54 state and grant-in-aid trails to ride in the state, […]