Why Does My Engine Knock? 3 Possible Explanations.

There are a few different reasons your engine might make a knocking, ticking or pinging sound. Let’s break each down and talk about what might be happening.

Is it an engine knocking sound, tick or ping?

One driver’s knock is another driver’s tick. Or ping. Still others compare the engine knocking sound they hear to marbles rolling around inside a coffee can.

The spontaneous ignition of air/fuel inside the cylinders is a common source of engine knock.

While the description of the sound may differ, the circumstances under which it occurs are often the same – low-speed, high-torque conditions common when you’re accelerating.

Engine knock typically occurs during low-speed, high-torque conditions, like when you’re accelerating.

How engine knock occurs

Say the clock has struck 5:00 and you make a bee-line to your truck and take off for home. When you mash the accelerator out of the parking lot, that’s when you hear an engine knocking sound. Or ping. When you let off the gas, it goes away.

This is likely due to either preignition or detonation. They’re effectively the same phenomenon, but they occur at different times.

In a properly running engine, spark-triggered ignition typically occurs a few degrees before the piston reaches top dead center (TDC). This careful timing ensures the downward force of the exploding fuel/air mixture works in tandem with downward piston momentum, resulting in optimum efficiency and power.

That’s bad timing

Pre-ignition (and its cousin, low-speed pre-ignition [LSPI]) are abnormal combustion events that throw off this precise balance. Under certain conditions, the fuel/air can spontaneously ignite too early in the combustion cycle. Sometimes low-octane fuel is to blame; sometimes it’s deposits on the piston crown.

LSPI Low Speed Pre-Ignition

Fuel with too low an octane rating for your engine can sporadically ignite prior to the piston reaching TDC.

Or, chunks of carbon can heat up and create a hot spot that effectively ignites the fuel/air before the plug fires. Then, when the plug does fire a fraction of a second later, the two flame fronts collide. In certain conditions, they can clash with the upward-moving piston. The resulting shock wave rattles the piston inside the cylinder, creating the knock, ping or can-of-marbles sound you hear.

Detonation has the same effect, except it occurs after the plug fires.

Computers in modern vehicles can detect engine knock and compensate by adjusting engine timing. Though it saves your engine from destroying itself, performance and fuel economy can suffer.

Tick, tick, tick

Say your engine is ticking like a time bomb, especially in the morning when it’s cold. You likely have a valve-train issue.

Your engine uses intake valves to feed clean air into the cylinders and exhaust valves to kick spent combustion gases out. The valves open and close thousands of time per minute in a choreographed whirlwind of activity.

top dead center valve timing

A finely balanced system of parts – rocker arms, valve stems, cam lobes, lifters – control their movements. The clearances between these parts, known as lash, can become loose (or sloppy, in automobile nomenclature). When that happens, all those moving parts clattering against each other can create a ticking sound.

It’s especially noticeable in the morning before the oil has had a chance to circulate throughout the upper end of the engine.

Many engines use hydraulic lifters, which use an oil-pressure-assisted plunger and spring to compensate for lash, helping ensure the system runs smoothly and quietly.

Proper oil pressure plays a big role in valve-train operation and noise. Low oil pressure can reduce the effectiveness of hydraulic lifters, increasing lash. This is most likely to occur with a low-quality conventional oil that thins at high temperatures, preventing the engine from developing good oil pressure.

If the rods are knockin’…

Rod knock is yet another possible explanation for your engine knocking sound.

Your engine is built with a designed clearance between the crankshaft journals and the connecting rods. In a properly running engine using a good oil, the motor oil fills those clearances and prevents metal-to-metal contact.

But, let’s say you’ve been using a poor-quality conventional oil.

At high temperatures, the oil thins and the fluid film weakens. The pressure between the crank journals and connecting rods squeezes the oil from the clearances. Now, metal is riding on metal, wearing the surfaces and widening the clearances. Eventually the clearances widen so much that you begin to hear the metal surfaces clattering against each other. Eventually, they’ll weld together and destroy the engine.

Quieting a noisy engine

This all sounds dire. But you can sometimes address pre-ignition by using a higher octane gas or by cleaning deposits from your engine with a fuel-system cleaner like AMSOIL P.i. Performance Improver.

Buy AMSOIL P.i.

Using a higher-quality oil that flows better in cold weather and maintains its viscosity when hot can sometimes quiet a valve-train tick.

Shop AMSOIL Synthetic Motor Oil

Rod knock is the worst of the three. Once the clearances between the crank journals and connecting rods have widened due to wear, it’s just a matter of time before catastrophic damage.

In any case, visit your mechanic and take care of the problem before it gets worse.

The bottom line…

The moral of the story is simply to pay a little more now to maintain your vehicle rather than spend a lot later to fix it.

Use a high-quality oil that stands up to extreme heat and maintains correct oil pressure. Periodically clean combustion chamber deposits with a fuel additive, such as AMSOIL P.i.

Doing so can help keep your vehicle running properly and quietly for years.

automatic transmission issues

Do Transmission Fluid Additives Work? John Baker| Feb 26, 2024 9:04 AM Walk the aisles of most auto parts stores and you’ll find multiple “mechanic-in-a-bottle”-type additives that claim to restore transmission performance. The claims made typically include some variation of the following: • Frees stuck valves to improve shifting • Fixes transmission slipping • Restores smooth […]

Understanding Oil Viscosity Viscosity is the measure of a fluid’s resistance to flow. _by David Hilgendorf|January 17, 2023 The physical properties of lubricants are measured by characteristics like viscosity, shear stability, high- and low-temperature performance, water resistance and volatility. Lubrication science seeks to optimize a lubricant’s performance by managing these properties using different base oils […]

Top 5 Skid Steer Maintenance Tips _by David Hilgendorf|September 29, 2023 Skid steers are built for tough construction, excavation, agricultural and other professional projects. Whether you’re clearing land, moving rocks or tearing down a wall, a skid steer is an excellent piece of equipment for many different jobs. But these nimble machines can be expensive […]

thermal runaway occurs when viscosity drops out and wear increases

How Often Should I Change Differential Fluid? Fluid change intervals depend on your vehicle, driving conditions and gear oil quality. Save time and cash first by improving the situation with this differential fluid solution! _by David Hilgendorf|Feb 26, 2023 A differential is a set of gears that allows a vehicle’s driven wheels to revolve at […]

New European oils for 2023 0W-30 and 10W-60

New AMSOIL Synthetic European Motor Oil Viscosities A new 10W-60 and 0W-30 for several BMW, Volkswagen and other fancy European cars. _by Brad Nelson|June 13, 2023 Those who know, know. The sophisticated engineering, finely-tuned performance and artistic styling of European cars can turn a daily commute into a grin-inducing experience. The design of these vehicles […]

EZ marine lower gear lube service

Service Marine Lower Units to Prevent Water Damage Preventing rust and other water-related problems in marine lower units. Most other Marine Gear Oils fail to make the grade. We learn more on that from our own customers when they make the switch. by David Hilgendorf|April 24, 2023 Water and gear lube don’t mix. Unfortunately, you […]